7针0.96寸OLED的HAL库代码（硬件SPI/全代码/stm32f1/CubeMX配置/包含有正负浮点数/100%一次点亮）
系列文章链接
HC-SR04超声波模块的使用
编码电机以及双电机驱动
4针 0.96'OLED的使用
更多有意思的文章点击“我的主页”
--------😐
更多有意思的视频 -----> B站 @想要亿只独角兽
--------😐
前言
- 之前发布了一篇硬件I2C的0.96' OLED驱动代码，这次就添加一篇硬件SPI的驱动代码。
其实改动的代码不多，对下面两个写命令和写数据的函数稍加改动即可。
void OLED_WR_DATA(uint8_t data) 和 void OLED_WR_CMD(uint8_t cmd)
目录
系列文章链接
前言
一、OLED驱动的基本功能
二、CubeMX中的设置
2.1. 配置时钟树
2.2. 配置硬件SPI
2.3. 接线以及最终管脚图
三、代码
3.1. oled.c
3.2. oled.h
3.3. oledfont.c
3.4. oledfont.h
3.5. main.h
3.6. main.c （仅测试使用）
四、推荐学习
总结
一、OLED驱动的基本功能
跟I2C那篇驱动代码的功能一致，这里再叙述一下。。。
1.可以正反相显示8X16，6x8的字符，数字，字符串
2.可以正反相显示16X16的汉字
3.可以正反相显示任意大小的图像
4.全屏水平滚动播放，部分屏幕水平滚动播放 ，全屏垂直水平滚动播放
5. 屏幕亮度调节，屏幕内容取反显示
6. 可以正反相显示8X16，6x8的正负浮点数
二、CubeMX中的设置
2.1. 配置时钟树
（1）点击RCC 开启HSE，并选择RC或晶体作为时钟源
（2）配置时钟树
最终最右侧显示为
2.2. 配置硬件SPI
需要配置的参数如下：
*********************************************************
* 引脚定义：
* OLED_CS OLED_RES OLED_DC ：OUTPUT Output push pull
*********************************************************
* SPI定义：
* Mode:Transmit only Master
* Hardware Nss Signal:Disable
* Data Size : 8Bits
* First Bit : MSB First
* CPOL : Low
* CPHA : 1 Edge
*********************************************************（1）选择SPI1；
将模式选择为 Transmit only Master （主机发送，从机接收）；Hardware Nss Signal: Disable ；
（2）SPI参数设定
其中时钟的预分频系数Prescaler可以设置的小一些，这样对应的波特率Baud Rate 就会比较大，相应的直观感受是OLED刷新的速度很快，屏闪感受变小。
（3）GPIO配置
PB0、PB1、PB10 都设置为 初始低电平，推挽输出，无上下拉电阻，高速输出 的模式
（4）烧录选SWD
2.3. 接线以及最终管脚图
********************************************************
* 接线：
* GND ---> GND
* VCC ---> 3.3V
* DO ---> SPI_SCK PA5
* D1 ---> SPI_MOSI PA7
* RES ---> OLED_RES PB0
* DC ---> OLED_DC PB1
* CS ---> OLED_CS PB10
*
********************************************************
三、代码
3.1. oled.c
>注：
> 1.上图中 Set Charge Pump （设置电荷泵）设置为0x8D,0x10即关闭了电荷泵;而程序中笔者开启了电荷泵，故设置为0x8D,0x14。而且把这一步放置在了初始化的最后。
> 2.笔者的初始化程序在对比度设置（红色字体处），预充电持续时间等数值大小上与上图不同，其实只要初始化思路一致，这些差异不会影响OLED的使用，这些个性化设置还需好好参读芯片手册**
/********************************************************/
/* 2022/9/30
* Unicorn_Yihao
* STM32 7针硬件SPI 0.96 OLED HAL库显示驱动
*********************************************************
* 引脚定义：
* OLED_CS OLED_RES OLED_DC OUTPUT Output push pull
*********************************************************
* SPI定义：
* Mode:Transmit only Master
* Hardware Nss Signal:Disable
* Data Size : 8Bits
* First Bit : MSB First
* CPOL : Low
* CPHA : 1 Edge
*********************************************************
* 接线：
* GND ---> GND
* VCC ---> 3.3V
* DO ---> SPI_SCK PA5
* D1 ---> SPI_MOSI PA7
* RES ---> OLED_RES PB0
* DC ---> OLED_DC PB1
* CS ---> OLED_CS PB10
*
*/
/********************************************************/#include "oled.h"/*********************************************************** 初始化命令,根据芯片手册书写***********************************************************/
uint8_t OLED_Init_CMD_Data[]={
0xAE, 0xD5, 0x80, 0xA8, 0x3F, 0xD3, 0x00, 0x40,0xA1, 0xC8, 0xDA,0x12, 0x81, 0xCF, 0xD9, 0xF1, 0xDB, 0x40, 0xA4, 0xA6,0x8D, 0x14,0xAF};/*** @function: void OLED_Init(void)* @description: OLED初始化* @return {*}*/
void OLED_Init(void)
{OLED_RES_Clr();HAL_Delay(200);OLED_RES_Set();uint8_t i = 0; for(i=0; i<23; i++){OLED_WR_CMD(OLED_Init_CMD_Data[i]);}}/*** @function: void OLED_WR_CMD(uint8_t cmd)* @description: 向设备写控制命令* @param {uint8_t} cmd 芯片手册规定的命令* @return {*}*/
void OLED_WR_CMD(uint8_t cmd)
{OLED_DC_Clr();OLED_CS_Clr();HAL_SPI_Transmit(&hspi1,&cmd,1,100); //需根据实际情况修改 OLED_CS_Set();OLED_DC_Set();
}/*** @function: void OLED_WR_DATA(uint8_t data)* @description: 向设备写控制数据* @param {uint8_t} data 数据* @return {*}*/
void OLED_WR_DATA(uint8_t data)
{OLED_DC_Set(); OLED_CS_Clr();HAL_SPI_Transmit(&hspi1,&data,1,100); //需根据实际情况修改 OLED_CS_Set();OLED_DC_Set();
}/*** @function: void OLED_On(void)* @description: 更新显示* @return {*}*/
void OLED_On(void)
{uint8_t i,n;for(i=0;i<8;i++){OLED_WR_CMD(0xb0+i); //设置页地址（0~7）OLED_WR_CMD(0x00); //设置显示位置—列低地址OLED_WR_CMD(0x10); //设置显示位置—列高地址for(n=0;n<128;n++)OLED_WR_DATA(1);}
}/*** @function: OLED_Clear(void)* @description: 清屏,整个屏幕是黑色的!和没点亮一样!!!* @return {*}*/
void OLED_Clear(void)
{uint8_t i,n;for(i=0;i<8;i++){OLED_WR_CMD(0xb0+i); //设置页地址（0~7）OLED_WR_CMD(0x00); //设置显示位置—列低地址OLED_WR_CMD(0x10); //设置显示位置—列高地址for(n=0;n<128;n++)OLED_WR_DATA(0);}
}/*** @function: void OLED_Display_On(void)* @description: 开启OLED显示* @return {*}*/
void OLED_Display_On(void)
{OLED_WR_CMD(0X8D); //SET DCDC命令OLED_WR_CMD(0X14); //DCDC ONOLED_WR_CMD(0XAF); //DISPLAY ON,打开显示
}/*** @function: void OLED_Display_Off(void)* @description: 关闭OLED显示* @return {*}*/
void OLED_Display_Off(void)
{OLED_WR_CMD(0X8D); //SET DCDC命令OLED_WR_CMD(0X10); //DCDC OFFOLED_WR_CMD(0XAE); //DISPLAY OFF，关闭显示
}/*** @function: void OLED_Set_Pos(uint8_t x, uint8_t y)* @description: 坐标设置* @param {uint8_t} x,y* @return {*}*/
void OLED_Set_Pos(uint8_t x, uint8_t y)
{OLED_WR_CMD(0xb0+y); //设置页地址（0~7）OLED_WR_CMD(((x&0xf0)>>4)|0x10); //设置显示位置—列高地址OLED_WR_CMD(x&0x0f); //设置显示位置—列低地址
}/*** @function: unsigned int oled_pow(uint8_t m,uint8_t n)* @description: m^n函数* @param {uint8_t} m,n* @return {unsigned int} result*/
unsigned int oled_pow(uint8_t m,uint8_t n)
{unsigned int result=1;while(n--)result*=m;return result;
}/*** @function: void OLED_ShowChar(uint8_t x, uint8_t y, uint8_t chr, uint8_t Char_Size,uint8_t Color_Turn)* @description: 在OLED12864特定位置开始显示一个字符* @param {uint8_t} x字符开始显示的横坐标* @param {uint8_t} y字符开始显示的纵坐标* @param {uint8_t} chr待显示的字符* @param {uint8_t} Char_Size待显示字符的字体大小,选择字体 16/12* @param {uint8_t} Color_Turn是否反相显示(1反相、0不反相)* @return {*}*/
void OLED_ShowChar(uint8_t x,uint8_t y,uint8_t chr,uint8_t Char_Size,uint8_t Color_Turn)
{unsigned char c=0,i=0;c=chr-' ';//得到偏移后的值if(x>128-1){x=0;y=y+2;}if(Char_Size ==16){OLED_Set_Pos(x,y);for(i=0;i<8;i++){if(Color_Turn)OLED_WR_DATA(~F8X16[c*16+i]);elseOLED_WR_DATA(F8X16[c*16+i]);}OLED_Set_Pos(x,y+1);for(i=0;i<8;i++){if(Color_Turn)OLED_WR_DATA(~F8X16[c*16+i+8]);elseOLED_WR_DATA(F8X16[c*16+i+8]);}}else{OLED_Set_Pos(x,y);for(i=0;i<6;i++){if(Color_Turn)OLED_WR_DATA(~F6x8[c][i]);elseOLED_WR_DATA(F6x8[c][i]);}}
}/*** @function: void OLED_ShowString(uint8_t x, uint8_t y, uint8_t *chr, uint8_tChar_Size, uint8_t Color_Turn)* @description: 在OLED12864特定位置开始显示字符串* @param {uint8_t} x待显示字符串的开始横坐标x:0~127* @param {uint8_t} y待显示字符串的开始纵坐标 y:0~7，若选择字体大小为16，则两行数字之间需要间隔2，若选择字体大小为12，间隔1* @param {uint8_t} *chr待显示的字符串* @param {uint8_t} Char_Size待显示字符串的字体大小,选择字体 16/12，16为8X16，12为6x8* @param {uint8_t} Color_Turn是否反相显示(1反相、0不反相)* @return {*}*/
void OLED_ShowString(uint8_t x,uint8_t y,char *chr,uint8_t Char_Size, uint8_t Color_Turn)
{uint8_t j=0;while (chr[j]!='\\0'){ OLED_ShowChar(x,y,chr[j],Char_Size, Color_Turn);if (Char_Size == 12) //6X8的字体列加6，显示下一个字符x += 6;else //8X16的字体列加8，显示下一个字符x += 8;if (x > 122 && Char_Size==12) //TextSize6x8如果一行不够显示了，从下一行继续显示{x = 0;y++;}if (x > 120 && Char_Size== 16) //TextSize8x16如果一行不够显示了，从下一行继续显示{x = 0;y++;}j++;}
}/*** @function: void OLED_ShowNum(uint8_t x,uint8_t y,unsigned int num,uint8_t len,uint8_t size2, Color_Turn)* @description: 显示数字* @param {uint8_t} x待显示的数字起始横坐标,x:0~126* @param {uint8_t} y待显示的数字起始纵坐标, y:0~7，若选择字体大小为16，则两行数字之间需要间隔2，若选择字体大小为12，间隔1* @param {unsigned int} num:输入的数据* @param {uint8_t } len:输入的数据位数* @param {uint8_t} size2:输入的数据大小，选择 16/12，16为8X16，12为6x8* @param {uint8_t} Color_Turn是否反相显示(1反相、0不反相)* @return {*}*/
void OLED_ShowNum(uint8_t x,uint8_t y,unsigned int num,uint8_t len,uint8_t size2, uint8_t Color_Turn)
{uint8_t t,temp;uint8_t enshow=0;for(t=0;t<len;t++){temp=(num/oled_pow(10,len-t-1))%10;if(enshow==0&&t<(len-1)){if(temp==0){OLED_ShowChar(x+(size2/2)*t,y,' ',size2, Color_Turn);continue;}else enshow=1;}OLED_ShowChar(x+(size2/2)*t,y,temp+'0',size2, Color_Turn);}
}/*** @function: void OLED_Showdecimal(uint8_t x,uint8_t y,float num,uint8_t z_len,uint8_t f_len,uint8_t size2, uint8_t Color_Turn)* @description: 显示正负浮点数* @param {uint8_t} x待显示的数字起始横坐标,x:0~126* @param {uint8_t} y待显示的数字起始纵坐标, y:0~7，若选择字体大小为16，则两行数字之间需要间隔2，若选择字体大小为12，间隔1* @param {float} num:输入的浮点型数据* @param {uint8_t } z_ len:整数部分的位数* @param {uint8_t } f_len: 小数部分的位数* @param {uint8_t} size2:输入的数据大小，选择 16/12，16为8X16，12为6x8* @param {uint8_t} Color_Turn是否反相显示(1反相、0不反相)* @return {*}*/
void OLED_Showdecimal(uint8_t x,uint8_t y,float num,uint8_t z_len,uint8_t f_len,uint8_t size2, uint8_t Color_Turn)
{uint8_t t,temp,i=0;//i为负数标志位uint8_t enshow;int z_temp,f_temp;if(num<0){z_len+=1;i=1;num=-num;}z_temp=(int)num;//整数部分for(t=0;t<z_len;t++){temp=(z_temp/oled_pow(10,z_len-t-1))%10;if(enshow==0 && t<(z_len-1)){if(temp==0){OLED_ShowChar(x+(size2/2)*t,y,' ',size2, Color_Turn);continue;}elseenshow=1;}OLED_ShowChar(x+(size2/2)*t,y,temp+'0',size2, Color_Turn);}//小数点OLED_ShowChar(x+(size2/2)*(z_len),y,'.',size2, Color_Turn);f_temp=(int)((num-z_temp)*(oled_pow(10,f_len)));//小数部分for(t=0;t<f_len;t++){temp=(f_temp/oled_pow(10,f_len-t-1))%10;OLED_ShowChar(x+(size2/2)*(t+z_len)+5,y,temp+'0',size2, Color_Turn);}if(i==1)//如果为负，就将最前的一位赋值‘-’{OLED_ShowChar(x,y,'-',size2, Color_Turn);i=0;}
}/*** @function: void OLED_ShowCHinese(uint8_t x,uint8_t y,uint8_t no, uint8_t Color_Turn)* @description: 在OLED特定位置开始显示16X16汉字* @param {uint8_t} x待显示的汉字起始横坐标x: 0~112，两列汉字之间需要间隔16* @param {uint8_t} y待显示的汉字起始纵坐标 y: 0~6 , 两行汉字之间需要间隔2* @param {uint8_t} no待显示的汉字编号* @param {uint8_t} Color_Turn是否反相显示(1反相、0不反相)* @return {*}*/
void OLED_ShowCHinese(uint8_t x,uint8_t y,uint8_t no, uint8_t Color_Turn)
{uint8_t t=0;OLED_Set_Pos(x,y);for(t=0;t<16;t++){if (Color_Turn)OLED_WR_DATA(~Hzk[2*no][t]); //显示汉字的上半部分elseOLED_WR_DATA(Hzk[2*no][t]); //显示汉字的上半部分}OLED_Set_Pos(x,y+1);for(t=0;t<16;t++){if (Color_Turn)OLED_WR_DATA(~Hzk[2*no+1][t]); //显示汉字的上半部分elseOLED_WR_DATA(Hzk[2*no+1][t]);//显示汉字的上半部分}
}/*** @function: void OLED_DrawBMP(uint8_t x0, uint8_t y0, uint8_t x1, uint8_t y1, uint8_t * BMP,uint8_t Color_Turn)* @description: 在OLED特定区域显示BMP图片* @param {uint8_t} x0图像开始显示横坐标 x0:0~127* @param {uint8_t} y0图像开始显示纵坐标 y0:0~7* @param {uint8_t} x1图像结束显示横坐标 x1:1~128* @param {uint8_t} y1图像结束显示纵坐标 y1:1~8* @param {uint8_t} *BMP待显示的图像数据* @param {uint8_t} Color_Turn是否反相显示(1反相、0不反相)* @return {*}*/
void OLED_DrawBMP(uint8_t x0, uint8_t y0, uint8_t x1, uint8_t y1, uint8_t * BMP,uint8_t Color_Turn)
{uint32_t j = 0;uint8_t x = 0, y = 0;if(y1%8==0)y = y1/8;elsey = y1/8 + 1;for(y=y0;y<y1;y++){OLED_Set_Pos(x0,y);for(x=x0;x<x1;x++){if (Color_Turn)OLED_WR_DATA(~BMP[j++]);//显示反相图片elseOLED_WR_DATA(BMP[j++]);//显示图片}}
}/*@brief 显示动图@param x0：起始列地址y0：起始页地址x1：终止列地址y1：终止页地址k: 帧个数m: 单帧数组大小BMP[][m]：存放动图代码的数组@retval 无*/
void OLED_DrawGIF(uint8_t x0, uint8_t y0, uint8_t x1, uint8_t y1, uint8_t k, int m, unsigned char GIF[][m])
{unsigned int j=0; //定义变量unsigned char x,y,i; //定义变量if(y1%8==0) y=y1/8; //判断终止页是否为8的整数倍else y=y1/8+1;for (i=0;i<k;i++) //从第一帧开始画{j = 0;for(y=y0;y<y1;y++) //从起始页开始，画到终止页{OLED_Set_Pos(x0,y);//在页的起始列开始画for(x=x0;x<x1;x++) //画x1 - x0 列{OLED_WR_DATA(GIF[i][j++]); //画图片的点 }}//delay_ms(80);//人为制造卡顿？？？}
}/*** @function: void OLED_HorizontalShift(uint8_t direction)* @description: 屏幕内容水平全屏滚动播放* @param {uint8_t} direction LEFT 0x27 RIGHT 0x26* @return {*}*/
void OLED_HorizontalShift(uint8_t direction){OLED_WR_CMD(0x2e);//停止滚动OLED_WR_CMD(direction);//设置滚动方向OLED_WR_CMD(0x00);//虚拟字节设置，默认为0x00OLED_WR_CMD(0x00);//设置开始页地址OLED_WR_CMD(0x07);//设置每个滚动步骤之间的时间间隔的帧频// 0x00-5帧， 0x01-64帧， 0x02-128帧， 0x03-256帧， 0x04-3帧， 0x05-4帧， 0x06-25帧， 0x07-2帧，OLED_WR_CMD(0x07);//设置结束页地址OLED_WR_CMD(0x00);//虚拟字节设置，默认为0x00OLED_WR_CMD(0xff);//虚拟字节设置，默认为0xffOLED_WR_CMD(0x2f);//开启滚动-0x2f，禁用滚动-0x2e，禁用需要重写数据
}/*** @function: void OLED_Some_HorizontalShift(uint8_t direction,uint8_t start,uint8_t end)* @description: 屏幕部分内容水平滚动播放* @param {uint8_t} direction LEFT 0x27 RIGHT 0x26* @param {uint8_t} start 开始页地址 0x00~0x07* @param {uint8_t} end 结束页地址 0x01~0x07* @return {*}*/
void OLED_Some_HorizontalShift(uint8_t direction,uint8_t start,uint8_t end)
{OLED_WR_CMD(0x2e);//停止滚动OLED_WR_CMD(direction);//设置滚动方向OLED_WR_CMD(0x00);//虚拟字节设置，默认为0x00OLED_WR_CMD(start);//设置开始页地址OLED_WR_CMD(0x07);//设置每个滚动步骤之间的时间间隔的帧频,0x07即滚动速度2帧OLED_WR_CMD(end);//设置结束页地址OLED_WR_CMD(0x00);//虚拟字节设置，默认为0x00OLED_WR_CMD(0xff);//虚拟字节设置，默认为0xffOLED_WR_CMD(0x2f);//开启滚动-0x2f，禁用滚动-0x2e，禁用需要重写数据}/*** @function: void OLED_VerticalAndHorizontalShift(uint8_t direction)* @description: 屏幕内容垂直水平全屏滚动播放* @param {uint8_t} direction 右上滚动 0x29* 左上滚动 0x2A* @return {*}*/
void OLED_VerticalAndHorizontalShift(uint8_t direction)
{OLED_WR_CMD(0x2e);//停止滚动OLED_WR_CMD(direction);//设置滚动方向OLED_WR_CMD(0x01);//虚拟字节设置OLED_WR_CMD(0x00);//设置开始页地址OLED_WR_CMD(0x07);//设置每个滚动步骤之间的时间间隔的帧频，即滚动速度OLED_WR_CMD(0x07);//设置结束页地址OLED_WR_CMD(0x01);//垂直滚动偏移量OLED_WR_CMD(0x00);//虚拟字节设置，默认为0x00OLED_WR_CMD(0xff);//虚拟字节设置，默认为0xffOLED_WR_CMD(0x2f);//开启滚动-0x2f，禁用滚动-0x2e，禁用需要重写数据
}/*** @function: void OLED_DisplayMode(uint8_t mode)* @description: 屏幕内容取反显示* @param {uint8_t} direction ON 0xA7 ，* OFF 0xA6 默认此模式，设置像素点亮* @return {*}*/
void OLED_DisplayMode(uint8_t mode)
{OLED_WR_CMD(mode);
}/*** @function: void OLED_IntensityControl(uint8_t intensity)* @description: 屏幕亮度调节* @param {uint8_t} intensity 0x00~0xFF,RESET=0x7F* @return {*}*/
void OLED_IntensityControl(uint8_t intensity)
{OLED_WR_CMD(0x81);OLED_WR_CMD(intensity);
}3.2. oled.h
/** oled.h** Created on: 2022年9月30日* Author: Unicorn_Yihao*/#ifndef __OLED_H__
#define __OLED_H__#include "main.h"
#include "oledfont.h"extern SPI_HandleTypeDef hspi1;#define OLED_RES_Clr() HAL_GPIO_WritePin(OLED_RES_GPIO_Port,OLED_RES_Pin,GPIO_PIN_RESET)//RES
#define OLED_RES_Set() HAL_GPIO_WritePin(OLED_RES_GPIO_Port,OLED_RES_Pin,GPIO_PIN_SET)#define OLED_DC_Clr() HAL_GPIO_WritePin(OLED_DC_GPIO_Port,OLED_DC_Pin,GPIO_PIN_RESET)//DC
#define OLED_DC_Set() HAL_GPIO_WritePin(OLED_DC_GPIO_Port,OLED_DC_Pin,GPIO_PIN_SET)#define OLED_CS_Clr() HAL_GPIO_WritePin(OLED_CS_GPIO_Port,OLED_CS_Pin,GPIO_PIN_RESET)//CS
#define OLED_CS_Set() HAL_GPIO_WritePin(OLED_CS_GPIO_Port,OLED_CS_Pin,GPIO_PIN_SET)void OLED_WR_CMD(uint8_t cmd);
void OLED_WR_DATA(uint8_t data);
void OLED_Init(void);
void OLED_Clear(void);
void OLED_Display_On(void);
void OLED_Display_Off(void);
void OLED_Set_Pos(uint8_t x, uint8_t y);
void OLED_On(void);
void OLED_ShowNum(uint8_t x,uint8_t y,unsigned int num,uint8_t len,uint8_t size2,uint8_t Color_Turn);
void OLED_Showdecimal(uint8_t x,uint8_t y,float num,uint8_t z_len,uint8_t f_len,uint8_t size2, uint8_t Color_Turn);
void OLED_ShowChar(uint8_t x,uint8_t y,uint8_t chr,uint8_t Char_Size,uint8_t Color_Turn);
void OLED_ShowString(uint8_t x,uint8_t y,char*chr,uint8_t Char_Size,uint8_t Color_Turn);
void OLED_ShowCHinese(uint8_t x,uint8_t y,uint8_t no,uint8_t Color_Turn);
void OLED_DrawBMP(uint8_t x0, uint8_t y0, uint8_t x1, uint8_t y1, uint8_t * BMP,uint8_t Color_Turn);
void OLED_DrawGIF(uint8_t x0, uint8_t y0, uint8_t x1, uint8_t y1, uint8_t k, int m, unsigned char GIF[][m]);
void OLED_HorizontalShift(uint8_t direction);
void OLED_Some_HorizontalShift(uint8_t direction,uint8_t start,uint8_t end);
void OLED_VerticalAndHorizontalShift(uint8_t direction);
void OLED_DisplayMode(uint8_t mode);
void OLED_IntensityControl(uint8_t intensity);void OLED_DrawDot(uint8_t x,uint8_t y);
void OLED_Draw_XLine(uint8_t x,uint8_t y,int length);
void OLED_Draw_YLine(uint8_t x,uint8_t y,int length);#endif
3.3. oledfont.c
/** oledfont.c** Created on: Jul 24, 2022* Author: Unicorn_Yihao*/
#include "oledfont.h"//8*6 ASCII字符集点阵
const unsigned char F6x8[][6] =
{0x00, 0x00, 0x00, 0x00, 0x00, 0x00,// sp0x00, 0x00, 0x00, 0x2f, 0x00, 0x00,// !0x00, 0x00, 0x07, 0x00, 0x07, 0x00,// "0x00, 0x14, 0x7f, 0x14, 0x7f, 0x14,// #0x00, 0x24, 0x2a, 0x7f, 0x2a, 0x12,// $0x00, 0x62, 0x64, 0x08, 0x13, 0x23,// %0x00, 0x36, 0x49, 0x55, 0x22, 0x50,// &0x00, 0x00, 0x05, 0x03, 0x00, 0x00,// '0x00, 0x00, 0x1c, 0x22, 0x41, 0x00,// (0x00, 0x00, 0x41, 0x22, 0x1c, 0x00,// )0x00, 0x14, 0x08, 0x3E, 0x08, 0x14,// *0x00, 0x08, 0x08, 0x3E, 0x08, 0x08,// +0x00, 0x00, 0x00, 0xA0, 0x60, 0x00,// ,0x00, 0x08, 0x08, 0x08, 0x08, 0x08,// -0x00, 0x00, 0x60, 0x60, 0x00, 0x00,// .0x00, 0x20, 0x10, 0x08, 0x04, 0x02,// /0x00, 0x3E, 0x51, 0x49, 0x45, 0x3E,// 00x00, 0x00, 0x42, 0x7F, 0x40, 0x00,// 10x00, 0x42, 0x61, 0x51, 0x49, 0x46,// 20x00, 0x21, 0x41, 0x45, 0x4B, 0x31,// 30x00, 0x18, 0x14, 0x12, 0x7F, 0x10,// 40x00, 0x27, 0x45, 0x45, 0x45, 0x39,// 50x00, 0x3C, 0x4A, 0x49, 0x49, 0x30,// 60x00, 0x01, 0x71, 0x09, 0x05, 0x03,// 70x00, 0x36, 0x49, 0x49, 0x49, 0x36,// 80x00, 0x06, 0x49, 0x49, 0x29, 0x1E,// 90x00, 0x00, 0x36, 0x36, 0x00, 0x00,// :0x00, 0x00, 0x56, 0x36, 0x00, 0x00,// ;0x00, 0x08, 0x14, 0x22, 0x41, 0x00,// <0x00, 0x14, 0x14, 0x14, 0x14, 0x14,// =0x00, 0x00, 0x41, 0x22, 0x14, 0x08,// >0x00, 0x02, 0x01, 0x51, 0x09, 0x06,// ?0x00, 0x32, 0x49, 0x59, 0x51, 0x3E,// @0x00, 0x7C, 0x12, 0x11, 0x12, 0x7C,// A0x00, 0x7F, 0x49, 0x49, 0x49, 0x36,// B0x00, 0x3E, 0x41, 0x41, 0x41, 0x22,// C0x00, 0x7F, 0x41, 0x41, 0x22, 0x1C,// D0x00, 0x7F, 0x49, 0x49, 0x49, 0x41,// E0x00, 0x7F, 0x09, 0x09, 0x09, 0x01,// F0x00, 0x3E, 0x41, 0x49, 0x49, 0x7A,// G0x00, 0x7F, 0x08, 0x08, 0x08, 0x7F,// H0x00, 0x00, 0x41, 0x7F, 0x41, 0x00,// I0x00, 0x20, 0x40, 0x41, 0x3F, 0x01,// J0x00, 0x7F, 0x08, 0x14, 0x22, 0x41,// K0x00, 0x7F, 0x40, 0x40, 0x40, 0x40,// L0x00, 0x7F, 0x02, 0x0C, 0x02, 0x7F,// M0x00, 0x7F, 0x04, 0x08, 0x10, 0x7F,// N0x00, 0x3E, 0x41, 0x41, 0x41, 0x3E,// O0x00, 0x7F, 0x09, 0x09, 0x09, 0x06,// P0x00, 0x3E, 0x41, 0x51, 0x21, 0x5E,// Q0x00, 0x7F, 0x09, 0x19, 0x29, 0x46,// R0x00, 0x46, 0x49, 0x49, 0x49, 0x31,// S0x00, 0x01, 0x01, 0x7F, 0x01, 0x01,// T0x00, 0x3F, 0x40, 0x40, 0x40, 0x3F,// U0x00, 0x1F, 0x20, 0x40, 0x20, 0x1F,// V0x00, 0x3F, 0x40, 0x38, 0x40, 0x3F,// W0x00, 0x63, 0x14, 0x08, 0x14, 0x63,// X0x00, 0x07, 0x08, 0x70, 0x08, 0x07,// Y0x00, 0x61, 0x51, 0x49, 0x45, 0x43,// Z0x00, 0x00, 0x7F, 0x41, 0x41, 0x00,// [0x00, 0x55, 0x2A, 0x55, 0x2A, 0x55,// 550x00, 0x00, 0x41, 0x41, 0x7F, 0x00,// ]0x00, 0x04, 0x02, 0x01, 0x02, 0x04,// ^0x00, 0x40, 0x40, 0x40, 0x40, 0x40,// _0x00, 0x00, 0x01, 0x02, 0x04, 0x00,// '0x00, 0x20, 0x54, 0x54, 0x54, 0x78,// a0x00, 0x7F, 0x48, 0x44, 0x44, 0x38,// b0x00, 0x38, 0x44, 0x44, 0x44, 0x20,// c0x00, 0x38, 0x44, 0x44, 0x48, 0x7F,// d0x00, 0x38, 0x54, 0x54, 0x54, 0x18,// e0x00, 0x08, 0x7E, 0x09, 0x01, 0x02,// f0x00, 0x18, 0xA4, 0xA4, 0xA4, 0x7C,// g0x00, 0x7F, 0x08, 0x04, 0x04, 0x78,// h0x00, 0x00, 0x44, 0x7D, 0x40, 0x00,// i0x00, 0x40, 0x80, 0x84, 0x7D, 0x00,// j0x00, 0x7F, 0x10, 0x28, 0x44, 0x00,// k0x00, 0x00, 0x41, 0x7F, 0x40, 0x00,// l0x00, 0x7C, 0x04, 0x18, 0x04, 0x78,// m0x00, 0x7C, 0x08, 0x04, 0x04, 0x78,// n0x00, 0x38, 0x44, 0x44, 0x44, 0x38,// o0x00, 0xFC, 0x24, 0x24, 0x24, 0x18,// p0x00, 0x18, 0x24, 0x24, 0x18, 0xFC,// q0x00, 0x7C, 0x08, 0x04, 0x04, 0x08,// r0x00, 0x48, 0x54, 0x54, 0x54, 0x20,// s0x00, 0x04, 0x3F, 0x44, 0x40, 0x20,// t0x00, 0x3C, 0x40, 0x40, 0x20, 0x7C,// u0x00, 0x1C, 0x20, 0x40, 0x20, 0x1C,// v0x00, 0x3C, 0x40, 0x30, 0x40, 0x3C,// w0x00, 0x44, 0x28, 0x10, 0x28, 0x44,// x0x00, 0x1C, 0xA0, 0xA0, 0xA0, 0x7C,// y0x00, 0x44, 0x64, 0x54, 0x4C, 0x44,// z0x14, 0x14, 0x14, 0x14, 0x14, 0x14,// horiz lines
};//16*8 ASCII字符集点阵
const unsigned char F8X16[]=
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//sp /00x00,0x00,0x00,0xF8,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x33,0x30,0x00,0x00,0x00,//! /10x00,0x10,0x0C,0x06,0x10,0x0C,0x06,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//" /20x40,0xC0,0x78,0x40,0xC0,0x78,0x40,0x00,0x04,0x3F,0x04,0x04,0x3F,0x04,0x04,0x00,//# /30x00,0x70,0x88,0xFC,0x08,0x30,0x00,0x00,0x00,0x18,0x20,0xFF,0x21,0x1E,0x00,0x00,//$ /40xF0,0x08,0xF0,0x00,0xE0,0x18,0x00,0x00,0x00,0x21,0x1C,0x03,0x1E,0x21,0x1E,0x00,//% /50x00,0xF0,0x08,0x88,0x70,0x00,0x00,0x00,0x1E,0x21,0x23,0x24,0x19,0x27,0x21,0x10,//& /60x10,0x16,0x0E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//' /70x00,0x00,0x00,0xE0,0x18,0x04,0x02,0x00,0x00,0x00,0x00,0x07,0x18,0x20,0x40,0x00,//( /80x00,0x02,0x04,0x18,0xE0,0x00,0x00,0x00,0x00,0x40,0x20,0x18,0x07,0x00,0x00,0x00,//) /90x40,0x40,0x80,0xF0,0x80,0x40,0x40,0x00,0x02,0x02,0x01,0x0F,0x01,0x02,0x02,0x00,//* /100x00,0x00,0x00,0xF0,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x1F,0x01,0x01,0x01,0x00,//+ /110x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0xB0,0x70,0x00,0x00,0x00,0x00,0x00,//, /120x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x01,0x01,0x01,0x01,//- /130x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,0x00,0x00,//. /140x00,0x00,0x00,0x00,0x80,0x60,0x18,0x04,0x00,0x60,0x18,0x06,0x01,0x00,0x00,0x00,/// /150x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x0F,0x10,0x20,0x20,0x10,0x0F,0x00,//0 /160x00,0x10,0x10,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//1 /170x00,0x70,0x08,0x08,0x08,0x88,0x70,0x00,0x00,0x30,0x28,0x24,0x22,0x21,0x30,0x00,//2 /180x00,0x30,0x08,0x88,0x88,0x48,0x30,0x00,0x00,0x18,0x20,0x20,0x20,0x11,0x0E,0x00,//3 /190x00,0x00,0xC0,0x20,0x10,0xF8,0x00,0x00,0x00,0x07,0x04,0x24,0x24,0x3F,0x24,0x00,//4 /200x00,0xF8,0x08,0x88,0x88,0x08,0x08,0x00,0x00,0x19,0x21,0x20,0x20,0x11,0x0E,0x00,//5 /210x00,0xE0,0x10,0x88,0x88,0x18,0x00,0x00,0x00,0x0F,0x11,0x20,0x20,0x11,0x0E,0x00,//6 /220x00,0x38,0x08,0x08,0xC8,0x38,0x08,0x00,0x00,0x00,0x00,0x3F,0x00,0x00,0x00,0x00,//7 /230x00,0x70,0x88,0x08,0x08,0x88,0x70,0x00,0x00,0x1C,0x22,0x21,0x21,0x22,0x1C,0x00,//8 /240x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x00,0x31,0x22,0x22,0x11,0x0F,0x00,//9 /250x00,0x00,0x00,0xC0,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,//: /260x00,0x00,0x00,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x60,0x00,0x00,0x00,0x00,//; /270x00,0x00,0x80,0x40,0x20,0x10,0x08,0x00,0x00,0x01,0x02,0x04,0x08,0x10,0x20,0x00,//< /280x40,0x40,0x40,0x40,0x40,0x40,0x40,0x00,0x04,0x04,0x04,0x04,0x04,0x04,0x04,0x00,//= /290x00,0x08,0x10,0x20,0x40,0x80,0x00,0x00,0x00,0x20,0x10,0x08,0x04,0x02,0x01,0x00,//> /300x00,0x70,0x48,0x08,0x08,0x08,0xF0,0x00,0x00,0x00,0x00,0x30,0x36,0x01,0x00,0x00,//? /310xC0,0x30,0xC8,0x28,0xE8,0x10,0xE0,0x00,0x07,0x18,0x27,0x24,0x23,0x14,0x0B,0x00,//@ /320x00,0x00,0xC0,0x38,0xE0,0x00,0x00,0x00,0x20,0x3C,0x23,0x02,0x02,0x27,0x38,0x20,//A /330x08,0xF8,0x88,0x88,0x88,0x70,0x00,0x00,0x20,0x3F,0x20,0x20,0x20,0x11,0x0E,0x00,//B /340xC0,0x30,0x08,0x08,0x08,0x08,0x38,0x00,0x07,0x18,0x20,0x20,0x20,0x10,0x08,0x00,//C /350x08,0xF8,0x08,0x08,0x08,0x10,0xE0,0x00,0x20,0x3F,0x20,0x20,0x20,0x10,0x0F,0x00,//D /360x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00,0x20,0x3F,0x20,0x20,0x23,0x20,0x18,0x00,//E /370x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00,0x20,0x3F,0x20,0x00,0x03,0x00,0x00,0x00,//F /380xC0,0x30,0x08,0x08,0x08,0x38,0x00,0x00,0x07,0x18,0x20,0x20,0x22,0x1E,0x02,0x00,//G /390x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08,0x20,0x3F,0x21,0x01,0x01,0x21,0x3F,0x20,//H /400x00,0x08,0x08,0xF8,0x08,0x08,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//I /410x00,0x00,0x08,0x08,0xF8,0x08,0x08,0x00,0xC0,0x80,0x80,0x80,0x7F,0x00,0x00,0x00,//J /420x08,0xF8,0x88,0xC0,0x28,0x18,0x08,0x00,0x20,0x3F,0x20,0x01,0x26,0x38,0x20,0x00,//K /430x08,0xF8,0x08,0x00,0x00,0x00,0x00,0x00,0x20,0x3F,0x20,0x20,0x20,0x20,0x30,0x00,//L /440x08,0xF8,0xF8,0x00,0xF8,0xF8,0x08,0x00,0x20,0x3F,0x00,0x3F,0x00,0x3F,0x20,0x00,//M /450x08,0xF8,0x30,0xC0,0x00,0x08,0xF8,0x08,0x20,0x3F,0x20,0x00,0x07,0x18,0x3F,0x00,//N /460xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00,0x0F,0x10,0x20,0x20,0x20,0x10,0x0F,0x00,//O /470x08,0xF8,0x08,0x08,0x08,0x08,0xF0,0x00,0x20,0x3F,0x21,0x01,0x01,0x01,0x00,0x00,//P /480xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00,0x0F,0x18,0x24,0x24,0x38,0x50,0x4F,0x00,//Q /490x08,0xF8,0x88,0x88,0x88,0x88,0x70,0x00,0x20,0x3F,0x20,0x00,0x03,0x0C,0x30,0x20,//R /500x00,0x70,0x88,0x08,0x08,0x08,0x38,0x00,0x00,0x38,0x20,0x21,0x21,0x22,0x1C,0x00,//S /510x18,0x08,0x08,0xF8,0x08,0x08,0x18,0x00,0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00,//T /520x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00,//U /530x08,0x78,0x88,0x00,0x00,0xC8,0x38,0x08,0x00,0x00,0x07,0x38,0x0E,0x01,0x00,0x00,//V /540xF8,0x08,0x00,0xF8,0x00,0x08,0xF8,0x00,0x03,0x3C,0x07,0x00,0x07,0x3C,0x03,0x00,//W /550x08,0x18,0x68,0x80,0x80,0x68,0x18,0x08,0x20,0x30,0x2C,0x03,0x03,0x2C,0x30,0x20,//X /560x08,0x38,0xC8,0x00,0xC8,0x38,0x08,0x00,0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00,//Y /570x10,0x08,0x08,0x08,0xC8,0x38,0x08,0x00,0x20,0x38,0x26,0x21,0x20,0x20,0x18,0x00,//Z /580x00,0x00,0x00,0xFE,0x02,0x02,0x02,0x00,0x00,0x00,0x00,0x7F,0x40,0x40,0x40,0x00,//[ /590x00,0x0C,0x30,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x06,0x38,0xC0,0x00,//\\ /600x00,0x02,0x02,0x02,0xFE,0x00,0x00,0x00,0x00,0x40,0x40,0x40,0x7F,0x00,0x00,0x00,//] /610x00,0x00,0x04,0x02,0x02,0x02,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//^ /620x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,//_ /630x00,0x02,0x02,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//` /640x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x19,0x24,0x22,0x22,0x22,0x3F,0x20,//a /650x08,0xF8,0x00,0x80,0x80,0x00,0x00,0x00,0x00,0x3F,0x11,0x20,0x20,0x11,0x0E,0x00,//b /660x00,0x00,0x00,0x80,0x80,0x80,0x00,0x00,0x00,0x0E,0x11,0x20,0x20,0x20,0x11,0x00,//c /670x00,0x00,0x00,0x80,0x80,0x88,0xF8,0x00,0x00,0x0E,0x11,0x20,0x20,0x10,0x3F,0x20,//d /680x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x1F,0x22,0x22,0x22,0x22,0x13,0x00,//e /690x00,0x80,0x80,0xF0,0x88,0x88,0x88,0x18,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//f /700x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x6B,0x94,0x94,0x94,0x93,0x60,0x00,//g /710x08,0xF8,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20,//h /720x00,0x80,0x98,0x98,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//i /730x00,0x00,0x00,0x80,0x98,0x98,0x00,0x00,0x00,0xC0,0x80,0x80,0x80,0x7F,0x00,0x00,//j /740x08,0xF8,0x00,0x00,0x80,0x80,0x80,0x00,0x20,0x3F,0x24,0x02,0x2D,0x30,0x20,0x00,//k /750x00,0x08,0x08,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//l /760x80,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x20,0x3F,0x20,0x00,0x3F,0x20,0x00,0x3F,//m /770x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20,//n /780x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00,//o /790x80,0x80,0x00,0x80,0x80,0x00,0x00,0x00,0x80,0xFF,0xA1,0x20,0x20,0x11,0x0E,0x00,//p /800x00,0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x0E,0x11,0x20,0x20,0xA0,0xFF,0x80,//q /810x80,0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x20,0x20,0x3F,0x21,0x20,0x00,0x01,0x00,//r /820x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x33,0x24,0x24,0x24,0x24,0x19,0x00,//s /830x00,0x80,0x80,0xE0,0x80,0x80,0x00,0x00,0x00,0x00,0x00,0x1F,0x20,0x20,0x00,0x00,//t /840x80,0x80,0x00,0x00,0x00,0x80,0x80,0x00,0x00,0x1F,0x20,0x20,0x20,0x10,0x3F,0x20,//u /850x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80,0x00,0x01,0x0E,0x30,0x08,0x06,0x01,0x00,//v /860x80,0x80,0x00,0x80,0x00,0x80,0x80,0x80,0x0F,0x30,0x0C,0x03,0x0C,0x30,0x0F,0x00,//w /870x00,0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x31,0x2E,0x0E,0x31,0x20,0x00,//x /880x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80,0x80,0x81,0x8E,0x70,0x18,0x06,0x01,0x00,//y /890x00,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x21,0x30,0x2C,0x22,0x21,0x30,0x00,//z /900x00,0x00,0x00,0x00,0x80,0x7C,0x02,0x02,0x00,0x00,0x00,0x00,0x00,0x3F,0x40,0x40,//{ /910x00,0x02,0x02,0x7C,0x80,0x00,0x00,0x00,0x00,0x40,0x40,0x3F,0x00,0x00,0x00,0x00,//} /920x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00};//| /93//部分汉字 阴码，列行式，逆向
const unsigned char Hzk[][32]=
{{0x40,0x22,0x14,0x08,0xF4,0x02,0x00,0xF8,0x08,0x08,0xFF,0x08,0x08,0xF8,0x00,0x00},{0x08,0x44,0x82,0x41,0x3F,0x00,0x20,0x63,0x21,0x21,0x3F,0x21,0x29,0x33,0x60,0x00},/*"独",0*/{0x20,0x10,0xE8,0x24,0x27,0x24,0x24,0xE4,0x24,0x34,0x2C,0x20,0xE0,0x00,0x00,0x00},{0x80,0x60,0x1F,0x09,0x09,0x09,0x09,0x7F,0x09,0x09,0x49,0x89,0x7F,0x00,0x00,0x00},/*"角",1*/{0x00,0x00,0x7C,0x54,0x55,0x56,0x54,0x7C,0x54,0x56,0x55,0x54,0x7C,0x00,0x00,0x00},{0x01,0x01,0x01,0xFD,0x45,0x45,0x45,0x45,0x45,0x45,0x45,0xFD,0x01,0x01,0x01,0x00},/*"兽",2*/};
//128*64图片
unsigned char BMP1[]={0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x80,0x00,0x40,0xE0,0xE0,0x60,0x00,0x40,0x80,0x00,0x00,0x00,0x80,0x80,0x60,0x60,0x10,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x90,0xB2,0x66,0x6E,0xEC,0xC9,0x83,0x02,0x00,0x40,0x80,0x00,0x0C,0x0C,0x01,0x03,0x07,0x0F,0x11,0x20,0x40,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x08,0x18,0x3B,0x37,0x66,0xEE,0xEE,0xCC,0x88,0x80,0x00,0x00,0x01,0x02,0x04,0x08,0x10,0x10,0x10,0x10,0x10,0x10,0x0F,0x00,0x00,0x00,0x00,0x00,0x00,0x3E,0x40,0x40,0x40,0x3E,0x00,0x7E,0x04,0x08,0x10,0x7E,0x00,0x7E,0x00,0x3C,0x42,0x42,0x42,0x42,0x00,0x7E,0x42,0x42,0x42,0x7E,0x00,0x7E,0x04,0x08,0x10,0x7E,/*"C:\\Users\\HP\\Desktop\\UNICORN.BMP",0*/};3.4. oledfont.h
/** oledfont.h** Created on: 2022年7月24日* Author: Unicorn_Yihao*/#ifndef __OLEDFONT_H__
#define __OLEDFONT_H__extern const unsigned char F6x8[][6];
extern const unsigned char F8X16[];
extern const unsigned char Hzk[][32];
extern unsigned char BMP1[];#endif /* OLED_OLEDFONT_H_ */
3.5. main.h
/* Private defines -----------------------------------------------------------*/#define OLED_RES_Pin GPIO_PIN_0
#define OLED_RES_GPIO_Port GPIOB
#define OLED_DC_Pin GPIO_PIN_1
#define OLED_DC_GPIO_Port GPIOB
#define OLED_CS_Pin GPIO_PIN_10
#define OLED_CS_GPIO_Port GPIOB3.6. main.c （仅测试使用）
/* USER CODE BEGIN Includes */
#include "oled.h"
/* USER CODE END Includes *//* USER CODE BEGIN 2 */OLED_Init(); //OLED初始OLED_Clear(); //清屏
//上面的初始化以及清屏的代码在一开始处一定要写OLED_ShowString(0,0,"UNICORN_LI",16, 1); //反相显示8X16字符串OLED_ShowString(0,2,"unicorn_li_123",12,0);//正相显示6X8字符串OLED_ShowCHinese(0,4,0,1); //反相显示汉字“独”OLED_ShowCHinese(16,4,1,1);//反相显示汉字“角”OLED_ShowCHinese(32,4,2,1);//反相显示汉字“兽”OLED_ShowCHinese(0,6,0,0); //正相显示汉字“独”OLED_ShowCHinese(16,6,1,0);//正相显示汉字“角”OLED_ShowCHinese(32,6,2,0);//正相显示汉字“兽”OLED_ShowNum(48,4,6,1,16, 0);//正相显示1位8X16数字“6”OLED_ShowNum(48,7,77,2,12, 1);//反相显示2位6X8数字“77”OLED_DrawBMP(90,0,122, 4,BMP1,0);//正相显示图片BMP1OLED_DrawBMP(90,4,122, 8,BMP1,1);//反相显示图片BMP1OLED_HorizontalShift(0x26);//全屏水平向右滚动播放//显示正负浮点数的代码
// float num1=-231.24;
// float num2=23.375;//OLED_ShowString(0,0,"Show Decimal",12,0);
//OLED_Showdecimal(0,4,num1,3,2,12, 0);
//OLED_Showdecimal(0,6,num2,2,3,16, 1);/* USER CODE END 2 */四、推荐学习
SSD1306驱动指令
https://blog.csdn.net/qq_39829913/article/details/104716829
总结
以上就是7针0.96寸OLED的HAL库版本的代码，全部按我这个操作100%一次点亮OLED屏，接下来我还会分享 软件I2C、软件SPI以及简易OLED多级菜单。
点点关注不迷路
这篇文章主要分享以及记录学习中的感悟，可能还有不足，还望大佬们在评论区提出，大家相互学习与进步。
欢迎大家积极交流，本文未经允许谢绝转载！！！