【HCIP】Huawei设备下IPV4IPV6共存实验

文章列表

方法一、普通的GRE将V6基于V4通讯

方法二、6to4的tunnel

方法三、双栈

方法一、普通的GRE将V6基于V4通讯

//方法一和方法二的前提，搭个简单的V4网络就行
[r1]int g0/0/0
[r1-GigabitEthernet0/0/0]ip address 12.1.1.1 24
[r1]router id 1.1.1.1
[r1-GigabitEthernet0/0/0]ospf 1
[r1-ospf-1]area 0
[r1-ospf-1-area-0.0.0.0]network 12.1.1.1 0.0.0.0[r2]int g0/0/1
[r2-GigabitEthernet0/0/1]ip address 12.1.1.2 24
[r2-GigabitEthernet0/0/1]int g0/0/0
[r2-GigabitEthernet0/0/0]ip address 23.1.1.1 24
[r2]router id 2.2.2.2
[r2]ospf 1
[r2-ospf-1]area 0
[r2-ospf-1-area-0.0.0.0]network 12.1.1.2 0.0.0.0
[r2-ospf-1-area-0.0.0.0]network 23.1.1.1 0.0.0.0[r3]int g0/0/1
[r3-GigabitEthernet0/0/1]ip address 23.1.1.2 24
[r3]router id 3.3.3.3
[r3]ospf 1
[r3-ospf-1]area 0
[r3-ospf-1-area-0.0.0.0]network 23.1.1.2 0.0.0.0

Begin......

[r1]ipv6
[r1-Tunnel0/0/0]int lo 0
[r1-LoopBack0]ipv6 enable 
[r1-LoopBack0]ipv6 address 10::1 64[r3]ipv6
[r3-Tunnel0/0/0]int lo0
[r3-LoopBack0]ipv6 enable 
[r3-LoopBack0]ipv6 address 30::1 64

【R1上】
#
interface Tunnel0/0/0ipv6 enable ipv6 address 55::1/64 tunnel-protocol gresource 12.1.1.1destination 23.1.1.2
#
【R3上】
#
interface Tunnel0/0/0ipv6 enable ipv6 address 55::2/64 tunnel-protocol gresource 23.1.1.2destination 12.1.1.1
#

//ping一下看tunnel口接通没

[r1]ipv6 route-static 30:: 64 55::2
//静态一写
[r3]ipv6 route-static 10:: 64 55::1

【验证】

方法二、6to4的tunnel

原理：

普通tunnel在多个V6网络构建为一个V6网络时，存在地址规划，指数的定义tunnel链路和路由信息，工程量巨大，极难维护；

6 to 4 tunnle可以让用于自行定义IPV6地址，均需要配置一条tunnel和一条路由即可；

****2002：：/16 6to4 tunnel 专用地址****

IPV4兼容地址--- 每一个IPV4地址都可以转换为一段IPV6地址；

本地V4网络地址为12.1.1.1 对应的V4兼容地址

12.1.1.1

0c01:0101=12.1.1.1

2002:c01:101::/64

本地V4网络地址为23.1.1.2 对应的V4兼容地址

23.1.1.2

1701:0102=23.1.1.2

2002:1701:102::/64

【记得把方法一搞那些IP undo掉(tunnel协议等等)】

【路由器上ipv6记得开，进无论哪个接口以后记得ipv6 enable】

//注意看我环回和tunnel上的ip可不一样嗷
固定的占48位，我设掩码64，细看这俩网络号不一样
【R1上】
#
interface LoopBack0ipv6 enable ipv6 address 2002:C01:101::1/64 
#
#
interface Tunnel0/0/0ipv6 enable ipv6 address 2002:C01:101:1::1/64 tunnel-protocol ipv6-ipv4 6to4source 12.1.1.1
#【R3上】
#
interface LoopBack0ipv6 enable ipv6 address 2002:1701:102::1/64 
#
#
interface Tunnel0/0/0ipv6 enable ipv6 address 2002:1701:102:1::1/64 tunnel-protocol ipv6-ipv4 6to4source 23.1.1.2
#

[r1]ipv6 route-static 2002:: 16 Tunnel 0/0/0[r3]ipv6 route-static 2002:: 16 Tunnel 0/0/0

【验证】

方法三、双栈

原理：

一台设备同时连接IPV4/IPV6网络，若目标IP为V6地址使用V6的源ip，通过V6的路由表传递；V4同理；

[Huawei]sysname r1
[r1]ipv6
[r1]int g0/0/0
[r1-GigabitEthernet0/0/0]ip address 12.1.1.1 24
[r1-GigabitEthernet0/0/0]int g0/0/1
[r1-GigabitEthernet0/0/1]ipv6 enable 
[r1-GigabitEthernet0/0/1]ipv6 address 13::1 64
[r1-GigabitEthernet0/0/1]int g0/0/2
[r1-GigabitEthernet0/0/2]ipv6 enable 
[r1-GigabitEthernet0/0/2]ip address 1.1.1.1 24
[r1-GigabitEthernet0/0/2]ipv6 address 1::1 64

[Huawei]sysname r2
[r2]int g0/0/1
[r2-GigabitEthernet0/0/1]ip address 12.1.1.2 24
[r2-GigabitEthernet0/0/1]int g0/0/0
[r2-GigabitEthernet0/0/0]ip address 24.1.1.1 24

[Huawei]sysname r3
[r3]ipv6
[r3-GigabitEthernet0/0/1]int g0/0/0
[r3-GigabitEthernet0/0/0]ipv6 enable 
[r3-GigabitEthernet0/0/0]ipv6 address 13::2 64
[r3-GigabitEthernet0/0/0]int g0/0/1
[r3-GigabitEthernet0/0/1]ipv6 enable 
[r3-GigabitEthernet0/0/1]ipv6 address 34::1 64

[Huawei]sysname r4
[r4]ipv6
[r4]int g0/0/1
[r4-GigabitEthernet0/0/1]ip address 24.1.1.2 24
[r4-GigabitEthernet0/0/1]int g0/0/0
[r4-GigabitEthernet0/0/0]ipv6 enable 
[r4-GigabitEthernet0/0/0]ipv6 address 34::2 64
[r4-GigabitEthernet0/0/0]int g0/0/2
[r4-GigabitEthernet0/0/2]ipv6 enable 
[r4-GigabitEthernet0/0/2]ipv6 address 2::1 64
[r4-GigabitEthernet0/0/2]ip address 2.2.2.1 24

👇RIP......

【注：上边是ipv4下的ripv2，下边是ipv6下的ripng】

[r1]rip 1
[r1-rip-1]version 2
[r1-rip-1]network 12.0.0.0
[r1-rip-1]network 1.0.0.0[r1]ripng 1
[r1-ripng-1]int g0/0/1
[r1-GigabitEthernet0/0/1]ripng 1 en	
[r1-GigabitEthernet0/0/1]ripng 1 enable 
[r1-GigabitEthernet0/0/1]int g0/0/2
[r1-GigabitEthernet0/0/2]ripng 1 enable

[r2]rip 1
[r2-rip-1]version 2
[r2-rip-1]network 12.0.0.0
[r2-rip-1]network 24.0.0.0

[r3]ripng 1
[r3-ripng-1]int g0/0/0
[r3-GigabitEthernet0/0/0]ripng 1 enable 
[r3-GigabitEthernet0/0/0]int g0/0/1
[r3-GigabitEthernet0/0/1]ripng 1 enable

[r4]rip 1
[r4-rip-1]version 2
[r4-rip-1]network 24.0.0.0
[r4-rip-1]network 2.0.0.0
[r4-rip-1]q
[r4]ripng 1
[r4-ripng-1]int g0/0/0
[r4-GigabitEthernet0/0/0]ripng 1 enable 
[r4-GigabitEthernet0/0/0]int g0/0/2
[r4-GigabitEthernet0/0/2]ripng 1 enable